# How to Determine the Size of Pulp Cord

## Full cord

Many factors influence the price of a full cord. One factor is the length of the piece. For example, the size of a piece of firewood can vary considerably. To determine the value of a full cord, a person must compare the face and total cord values of different lengths.

In addition to log length, full cord size is determined by depth. A full cord contains about one hundred and twenty cubic feet of wood. Its depth is 48 inches (1.2 m or 122 cm). This measurement is essential because the depth of a full cord differs from the face cord. It is necessary to check the complete cord size regulations in your state.

In the United States and Canada, the length of a cord is usually at least eight feet long. A complete line weighs approximately two to three tons. The size and diameter of a cable vary depending on the type of wood used for the production. Loblolly and shortleaf pines weigh approximately two tons per cord, while slash pines are heavier and have a higher specific gravity.

## The average length of wood in a face cord

If you plan to make a fireplace, you’ll need to calculate the average length of wood in a face cord. This measurement is easier to calculate if you’ve measured the entire wood stack. A full cord’s average length is 4 feet or 1.2 meters, and its overall volume must be 180 cubic feet or 5.1 cubic meters. You can find this number by measuring the depth and width of each log and using the average length of each record to calculate the full-cord value.

Face cords can vary in size but typically are 16 to 18 inches long. In addition, a face cord can go in-depth, ranging from 16 to 24 inches. For this reason, it’s essential to know how much wood is in a face cord before you make your final purchase.

The average length of wood in a face cord varies, but it should be at least 16 inches deep and four feet high. A face cord of wood can be divided into 16-inch lengths, but it doesn’t have to be exact. If the seller is hesitant to give you the same length of a face cord, you can ask for the size of the entire line. Similarly, if a seller is unsure of the depth of a face cord, you can ask if the whole length is the same as the height and width of a complete line.

You can choose from complete or face cords when ordering firewood for a fireplace. Face cords are smaller than full cords because they contain only one stack. A face cord has one-third of a cord’s volume, which is about 42.7 cubic feet.

## Value of a full cord

A full pulp cord is a measurement of the dry volume of pulpwood. In the United States and Canada, this unit equals approximately 128 cubic feet of pulpwood stacked in a single stack. This measurement is based on the dimensions of four feet long by four feet wide by eight feet high.

Full pulp cords vary in price depending on length, but a total cord costs around \$266 per cord. In addition, there are face cords, which are only a foot or two deep. As a result, a full line will typically be two feet in depth. There is also a difference in moisture value, which will be reflected in the price.

A full cord’s average log length should be four feet (1.2 meters), bringing the total volume to 180 cubic feet (5.1 cubic meters). Depending on the size of the pieces of wood, it may take several cords to make a full cord. Fortunately, the total cord value can be estimated with the help of the face cord measurement. In addition to the face cord measurement, you can calculate the volume of a full cord by figuring out its depth.

A full cord may also be referred to as a sawlog. These logs may be larger than a pulp cord, but these sizes are sometimes different. You will want to measure the average piece length if you sell firewood.

## Cost of a full cord

There are a few different ways to measure firewood, but using a “face cord” is the most common. A face cord is a standard 16-inch log. It is eight feet long, four feet high, and about one-third of the length of a complete line.

A full cord of firewood typically costs \$150-\$500. It can last anywhere from six to twelve weeks when burned twice daily. A complete line of hardwoods will last about three months, while softwoods will last about six weeks. In a northern climate, you may need two cords of firewood per winter. Fireplace inserts are also available to increase your home’s heating efficiency.

The length of a full cord will vary depending on the logs and other factors. Typically, an entire cable contains around 85 cubic feet of solid wood, while the rest is void. The term ‘full cord’ came about because the original unit of measurement was a cord or string used to measure a pile of wood.

Knowing how much wood you’ll need for a fire is essential. If you buy firewood for your home, you will want to split it before storing it. Then, cut it to the correct length. You can then split the wood and stack it neatly. If hiring a wood hauler, make sure you know how many cubic feet your wood hauler has and how tightly it can be stacked. It will also help you determine the price.

## Standard measurements for timber and pulpwood

Timber and pulpwood are often measured by the volume they contain. The importance of saw logs is usually measured in cubic feet, but other measurements can also be used. For example, a pile of four-foot-wide by eight-foot-long wood is approximately 160 cubic feet. In contrast, a rise of the exact dimensions but less than one hundred twenty cubic feet is called a short cord. Similarly, the cubic foot is used in forest inventories and growth and yield studies. In the United States, this measurement is based on a cord, a standard length of 90 cubic feet of solid wood. However, the actual volume of wood depends on several factors, such as the size of the pieces, the presence of bark, and the method of stacking.

A tree with a DBH of 16 inches has an inside bark diameter of 12.8 inches at the top of its first log and would be assigned a form class of 80. Another standard measurement in the timber and pulpwood industry is the “Scribner” decimal, which rounds to the nearest ten board feet. A log with an upper diameter of seventeen and a half feet would be assigned a form class of 80, while a log with an upper diameter of five and a half feet would be classified as a D60. The difference between the upper diameter and the actual volume cut is called an overrun. It is usually the result of various factors, including improved sawmill efficiency, a little saw kerf, or slabs cut outside the scale cylinder.

Loggers used to make less accurate measurements when they had ample supplies of cheap timber and plentiful labor. However, the dwindling supply of wood has led to higher production costs, and, as a result, timbermen must make more accurate estimates of log volume.