The Difference Between Pulp Cord and Cord

Do you want to know the difference between a pulp and a cord? Here are the main differences between a cord and a pulp. Considering the type of wood used, a pulp cord produces more heat than a cord of soft maple. However, a white birch or basswood line will yield less heat than a cord of hardwoods.

Face cord

Face cord prices differ from total cord prices, but they are close to each other. This means you must compare the prices of face cord and entire cord pieces of the same length to know which is more cost-effective. You can compare the costs of different sizes by calling various dealers and asking them to give you the price per piece.

Face cords are usually stacked 4 feet by 8 feet, and a pulp cord has three face cords that are each 16″ long. Typically, a full pulp cord will take approximately two to three truckloads. A typical truckload of mixed northern hardwoods will use about 260 gallons of propane or oil, while a ton of dry wood chips will use between 60 and 85 gallons of oil or propane.

Firewood is usually measured in cubic inches, but a face cord is generally four feet wide by eight feet long. Firewood logs are usually about 12 to 20 inches in diameter. To qualify as a face cord, firewood logs must be stacked tightly and without apparent gaps.

The Difference Between Pulp Cord and Cord image 3

In comparison to full cords, face cords are generally much cheaper. A complete cable contains 100 square feet of wood, and a face cord is only a third of a complete line. A face cord is a good size for most wood needs. You can compare the prices of face cords with complete cables to see which is most cost-effective for your budget.

Full cord

When comparing face cord and total pulp cord prices, it is essential to understand that a face cord will be less expensive than a full cord. It is necessary to consider the length of the pieces when comparing the face cord and total cord values. The size of a part will determine the price, and the difference between the two can be a significant factor in deciding which one is better for your budget.

A typical logging truck holds around eight to ten cords, depending on the truck’s size. A load with all big logs is more efficient than a mix of minor stuff. The type of wood used will also affect the amount of heat the bag will produce. Hardwoods produce more heat, while soft maple, white birch, basswood, and balsam produce less heat. For this reason, hardwoods are more valuable than soft maple, basswood, and balsam.

Many mills purchase logs by weight. It is easier to weigh truckloads than weigh each cord by hand. Therefore, many mills convert weight to the cable using a weight-to-cord conversion factor. While this may reflect the line somewhat, it may also vary based on MCs.

The Difference Between Pulp Cord and Cord image 2

Full cords can be too large for most fireboxes. You may have to split a full line to fit it in your firebox. Fortunately, you can get face cords that are only half the size of an entire thread. In addition, the face cord is also a third of the depth of a complete line.

Another way to measure firewood is by rick. While the terms are not always defined, some sellers will refer to ricks as “full cord.” However, it can be equivalent to a full cord in the U.S., so you’ll want to find out how many ricks a piece of wood weighs.

Ton

Tons and cords are terms used to describe the weight of wood. A cord of wood weighs about 2.3 tons, and a ton is about 2000 pounds. A cord can be as big as eight feet in diameter. In comparison, a thousand board feet is about 2500 pounds. The density of wood varies, so the weight of a cord will be around 15 to 50 percent lighter than the weight of lumber. Tons are also used to measure the volume of pulpwood. Wood chips and pellets are often delivered in “tons” to pulp mills.

Tons and cords are measured differently by different countries. In the U.S., a line contains approximately one hundred cubic feet of wood, equivalent to a stack four feet wide by four feet high and eight feet long. However, regulations vary from state to state, so it is important to check local laws before purchasing.

The Difference Between Pulp Cord and Cord image 1

Tons are also used to measure pulpwood in Canada and the United States. In the United States, a cord is defined by statute. The National Institute of Standards and Technology Handbook 130 defines the term cord to create uniform regulations for the sale of fireplace wood. The term is also used in Canada and other English-speaking countries. In New Zealand, however, there is no legal definition.

Conversion factor

In the timber industry, a cord is a unit of dry volume. It is often used to measure firewood and pulpwood. One line contains approximately 128 cubic feet or 3.6 cubic meters of wood. Its name likely comes from the fact that it measures the three dimensions of a well-stowed bundle of wood. However, the size of a cord is one of many factors affecting its volume. For example, the thickness of a line varies depending on the MC.

Hardwood timber is divided into two types – pulpwood and saw wood. The latter is measured in merchantable feet and is usually 8 inches DBH or higher. Conversion factors for hardwood sawtimber can vary, and the average diameter of a hardwood tree will influence the conversion factor. For example, a saw timber log with an average merchantable height of four feet will produce a better conversion factor than one with a diameter of four inches.

The volume of a cord can be converted to tons by multiplying the book by the appropriate tons/volume. This conversion factor can be used for both MBF and DBH. A cord of MBF pine sawtimber weighs approximately 260 pounds per cord. The weight of a line is much higher for slash pine.

The Difference Between Pulp Cord and Cord image 0

When weighing wood, one should also remember that its volume is inconsistent unless it is appropriately stacked. The pieces of wood in a loose stack will be more random and, therefore, will take up more space than those in tightly stacked bundles. As such, it is finding the accurate volume of a cord of wood takes a lot of work. However, it is recommended that a line of timber have a book of at least 180 cubic feet.

Add a comment