Wood Processor Troubleshooting Hydraulics

There are several factors that can cause your wood processor to malfunction, including the power source and hydraulic pressure. Proper maintenance is necessary to prevent these problems. In addition, you should periodically check the hydraulic fluid. Air in the lines can also cause problems. If you experience frequent malfunctions, call a mechanic for assistance.

Log splitter problems are caused by power source and hydraulic pressure

When you use a log splitter, it is necessary to check the hydraulic pressure and power source of the log splitter regularly. If they are not both correct, the log splitter may experience problems. Make sure that the hydraulic hoses and socket plugs are not blocked and that they are plugged correctly. It is also important to change the hydraulic fluid as needed.

Hydraulic log splitters use hydraulic pistons to move the plates. Oil leaks or air in the system can reduce the driving force, which results in slow plate movement. You should keep the oil warm during cold weather by storing the log splitter under a cover. Another common problem is clogged filters, which restrict the oil’s movement through the system.

Wood Processor Troubleshooting Hydraulics image 3

When these two factors are in balance, a log splitter can work properly for many years. In addition, a clean air filter and spark plug are two other important factors to ensure a smooth operation. If you use an electric log splitter, there is also a chance that you might experience problems with the power source. An extension cable may also cause the problem.

Another common problem with a log splitter is the motor stalling under load. If you have a faulty power source, the motor may die, even though the fuel tank is full. You can also experience issues with the hydraulic pressure and power source. Make sure you regularly check these two aspects to ensure a stable and functional log splitter.

When you use a log splitter, make sure you are using the correct power source and hydraulic pressure. Most home-made log splitters use single-stage pumps. These are slow and do not have high-pressure relief valves, so you need a powerful engine. In addition, single-stage pumps do not come with a high-pressure relief valve, so you need to make sure you have a directional valve for the hydraulic oil. Next, you need to check cylinder diameter. The larger the cylinder diameter, the more force the hydraulic pressure will have.

Wood Processor Troubleshooting Hydraulics image 2

Hoses

There are several components to consider when troubleshooting your wood processor hydraulics. The first component is the horsepower of the machine, which is necessary to split large logs. Another important aspect is displacement, which refers to the amount of water a pump can hold. A high displacement allows the water to pass quickly through the logs.

Hydraulic pumps are responsible for delivering pressurized hydraulic fluid to the hydraulic arm. Over time, these pumps develop problems and wear out. One of the most common problems is leaks from the pump. To repair this issue, disassemble the pump and replace all the seals. You should also test the hydraulic system to ensure that everything is working properly.

Seals

If your wood processor isn’t cutting wood as quickly as it should be, you should consider some of the common hydraulic troubleshooting issues. These issues can cause your machine to shake and vibrate. You should first check the level of the hydraulic oil and top it off, if necessary. You can also fix a hydraulic problem by cycling the pressure plate back and forth to clear air.

Wood Processor Troubleshooting Hydraulics image 1

Air in lines

If you notice that air is escaping from the hydraulic lines, your equipment may have a leak. If this occurs, you need to check the hydraulic oil and top it up if necessary. If this doesn’t fix the problem, you can try cycling the pressure plate back and forth and opening the bleed valve. This should relieve the air and allow the hydraulic system to work again.

If the log splitter is vibrating, the problem could be air in the hydraulic lines or a low level of hydraulic oil. You can check the oil level by opening the bleed valve and cycling the pressure plate back and forth. If it still doesn’t fix the problem, you should check the valves and check the oil level in the hydraulic lines.

Low hydraulic oil level

If your wood processor suddenly stops working, it may be due to a low hydraulic oil level. The fluid in the hydraulic system is drawn into cylinders and hoses and must be at the correct level to continue operating. If the oil level is low, you should check the hydraulic reservoir and add more if necessary. The hydraulic system can be dangerous if it runs dry, as hydraulic oil has a tendency to overflow due to the heat generated by the machine and the law of fluid expansion. Be sure to tighten the hydraulic oil dipstick, and dispose of used hydraulic oil at a proper disposal facility.

Wood Processor Troubleshooting Hydraulics image 0

Check the hydraulic oil level in your wood processor regularly. Make sure the oil level is around 3/4. Ensure the hydraulic fluid level is at least two to four inches above the top of the machine. If the oil level is lower than the bottom of the machine, remove the oil filling plug and add more oil.

Add a comment